Spectrum Technologies

Knowledgebase Home | Glossary | Favorites | Login Knowledgebase Home | Glossary | Favorites | Login
Search the Knowledgebase Browse by Category

Continue
Advanced Search
* Query:
  Categories:
  Rated:
Search Results for "error 513 unable to contact watch dog"
There were 66 articles found for your query: (Page 1 of 4)     «« |  Prev | 1 | 2 | 3 | 4 | Next | »»
  1. Weather Station MaintenanceWeather Station Maintenance [Article]
    One of the reasons that the WatchDog 2000-series weather stations are so widely used

  2. Getting the "ERR" message on my TDR300 meterGetting the "ERR" message on my TDR300 meter [Article]
    ...ly, the meter must be sent in for service. However, there is one cause for which it may be possible to get the meter functioning. Remove the face

  3. No GPS Found with Field Scout TDR MeterNo GPS Found with Field Scout TDR Meter [Article]


  4. Meter prematurely gives "READING COMPLETE" message.Meter prematurely gives "READING COMPLETE" message. [Article]
    ...is being withdrawn from the soil. This is similar to second part of solution for !! Depth Error !! e...

  5. !Error- Too Fast! message!Error- Too Fast! message [Article]
    Probe is being inserted too quickly. If the meter is inserted faster than 1 inch per 1 second, the ASABE standard states that the reading s

  6. !! Depth Error !! message!! Depth Error !! message [Article]
    This error message indicates that the meter missed a depth reading. This can happen when: a) The speed of insertion exceeds the meter's abilit

  7. EXCESSIVE FORCE errorEXCESSIVE FORCE error [Article]
    Load cell cannot support more than 250lb without permanent damage. Move a few feet away to another measuring spot and try again.

  8. No measurementNo measurement [Article]
    Check sensor block for cracks. Replace block or contact Spectrum.

  9. Real-time weather monitor is not working / will not startReal-time weather monitor is not working / will not start [Article]
    The real-time weather monitor displays current conditions (updated every 15 seconds). It requires a direct wired connection or direct wireless connection from the weather statio

  10. Error Message "Unable to connect to the Logger. Overflow"Error Message "Unable to connect to the Logger. Overflow" [Article]
    The "Overflow" error message indicates that there is some bug in the SpecWare. Reinitializing the logger header will probably fix the problem (see attached file). If there is data that

  11. LCD Display will not turn onLCD Display will not turn on [Article]
    ... LCD is damaged. If replacing the 4 AAA batteries (located beneath the face plate) does not help, contact Spectrum Technologies for ass

  12. My Cardy sensor will not hold calibration (2300)My Cardy sensor will not hold calibration (2300) [Article]
    These sensors wear out over time. Replace sensor. Item # 2340, or Contact Spectrum. Cardy NO3- Trouble Shooting What are the correct standards?

  13. My computer can connect to the dial-up modem but I cannot contact the WatchDog weather station.My computer can connect to the dial-up modem but I cannot contact the WatchDog w... [Article]
    When trying to connect to a weather station with a telephone connection, pay attention to the messages that appear in the lower left corner of the Specware screen. You should see messages such

  14. Error Message "Run-time error 63: bad record number" (SPAD 502 meter)Error Message "Run-time error 63: bad record number" (SPAD 502 meter) [Article]
    If the SPAD meter is turned off and immediately turned back on, a capacitor in the data logger's microcontroller circuit will not have time to completely power down.&nb

  15. Getting E07 when trying to calibrate the IQ 150 (2162)Getting E07 when trying to calibrate the IQ 150 (2162) [Article]
    The probe has failed and needs to be replaced. This error code is not related to the chassis.

  16. Error Message "Bad Data Returned X[72]"Error Message "Bad Data Returned X[72]" [Article]
    This message appears if the paperclip test is done with the interface cable connected to a logger or weather station. This very likely indicates that the correct Com port has been selected. Remove t

  17. Error Message "Division by zero"Error Message "Division by zero" [Article]
    The "Division by Zero" error message can appear if there are too many files in the Specware directo...

  18. Getting a "Sensor Error" message when connecting the barometric pressure sensor to a weather station.Getting a "Sensor Error" message when connecting the barometric pressu... [Article]
    The weather station should be running firmware version 7.0 or greater. The firmware version can be seen in the uppper right corner of the Launch Options

  19. Error Message "Unable to Write WatchDog Header"Error Message "Unable to Write WatchDog Header" [Article]


  20. Error Message: Cannot relaunch Shuttle until all data has been downloadedError Message: Cannot relaunch Shuttle until all data has been downloaded [Article]
    The shuttle can only be launched when the LCD screen reads "off". This indicates that there is no data on the shuttle that has not been downloaded. If there are shuttle positions that have not yet b

(Page 1 of 4)     «« |  Prev | 1 | 2 | 3 | 4 | Next | »»